Do you have an alternative for part 27S8-*-1AB?
- Mon - Fri : 09:00 - 17:00
- [email protected]
Do you have an alternative for part 27S8-*-1AB?
What stud length do I need with a MTHFTLC-*SK part?
Best is to use an example.
For instance, you have a panel thickness P of 2.5mm and a frame thickness of 1.5mm.
What's the correct part number MTHRPM22A or MTHRPM25A?
MTHRPM22A was an error in our old catalog.
Can Turnlock supply the 26S13-*-* parts?
The part 26S13-*-* all are steel with cadmium plating with a folding wing handle:
Yes, we have LN29711 parts available, however we consult to buy the alternative ROHS zinc plated version instead of the Cadmium plated version.
Pricing is also way higher of the Cadmium plated versions.
Here you see an installed wing head stud MTHTLW-1S on an electrical circuit board.
Can Turnlock provide the SK27S3-*S parts?
Turnlock can provide the MTHFTLC-*SK parts.
It has the same mechanical and dimensional properties.
Please find below the cross references.
Do you have an alternative part for 27S3-*S?
Yes, we have our stainless steel stud MTHFTLC-*SK
Please find below the cross references:
For the stud JN0426-05 the
Do you have the countersunk receptacle available 26R6-4BB?
Yes, we have an alternative version available of 26R6-4BB:
MTHRLWC26SK
It has the same dimensions and technical properties as 26R6-4BB.
Can You Supply the part LN29711-1 ?
What can you do about the adjustable receptacle sticking out?
Question:
We have installed on our helicopter:
MTHRA24HSA
MTHWFS
MTHTLC-3S
We are happy about the system, but it seems MTHTLC-3S is too high for our configuration since we needed to adjust receptacle MTHRA24HSA. The threaded part sticks out about 4mm, which seems too much.
The adjustable receptacle would also work with MTHTLC-2S or even MTHTLC-1S.
The biggest issue is that the adjustable receptacle sticks out.
Does Turnlock have the old MS2500 parts available?
Turnlock can supply the alternative Medium duty Tiny Housed Small studs.
They're made according to MS2500.
Does Turnlock have the 26R5-* receptacles available?
The alternative part for 26R5-13 is MTHRSPM26ZY slim panel mount yellow zinc receptacle.
Is there a stainless steel version of the knurled slotted head stud of MTH-series?
Yes there is.
It is made from stainless with electropolished surface, therefore it is rather shiny.
Does Turnlock have old 2800 parts available?
Yes we have these available under our brand MTHB-series or Medium duty Tiny Housed Bearing - series.
Here you can find a list of part numbers:
Here are the Slotted head part numbers:
This is the list of the cross head part numbers:
These are the old part numbers of the Torx headed studs:
All these studs can be used with the MTH receptacles.
To find the exact part number you need, please contact us.
Does chrome plating have a better corrosion resistance than zinc plated parts?
Yes, Chrome plating will have a better corrosion resistance and will be generally better to use in marine environments than zinc.
For example, the part MTHTLK-*C
The results will be pretty close to each other and the thickne
Select your stud by using below table. the amount of protrusion of the receptacle MTHRTA16A or MTHRTA16S
below table is valid only when your upper plate measure = 0mm (which is never the case)
NTA12852 parts can have a leadtime of more then a year and will cost you a fortune. If you are in
Do you have an alternative for the part 26R3-1?
Yes we do have an alternative for 26R3-1, which is the Turnlock part MTHRPM2HA
When you require a quote for our alternative of 26R3-1, please contact [email protected]
Does there exist a bracket mount to use with the MTH-series?
The new bracket developed for the MPP-series also matches for the MTH-series.
The first thing you'll need to take care off is to select the correct retaining washer.
MTHWFS is a washer which is a lot easier and much faster to install than the MTHWSS: